![]() They must first be updated to 6.3.5 then 6.5.2 and then onto 6.7.x. – ReadyNAS 202, 204, 212 and 212 must not be updated directly to 6.7.x from 6.3.x. They must first be updated to either 6.2.5 or 6.3.5 then to 6.5.2 and then onto 6.7.x. – ReadyNAS 102, 104, and 2120 must not be updated directly to 6.7.x from 6.3.x or older firmware. – Devices updated with 6.7.1 firmware should not be downgraded to earlier firmware versions. – Fixed a GUI issue where the Snapshots button would not work in the presence of a volume with no shares. – Fixed an issue where PHP support would not be enabled after installing apps requiring PHP. – Reduced the time it takes for defrag operations, by shrinking the target extent size. – Fixed an issue where apps could not be installed after factory defaulting with a >16TB volume. – Send email notifications when volume maintenance tasks are started. – Fixed an issue where backwards clock adjustments would pause stat updates used by performance graphs. – Added support for PSU monitoring after hot-adding a new PSU. ![]() – Fixed potentially incorrect disk fault LED status. – Fixed an issue where rsync local-to-remote backup jobs would only back up the top-level folder. – Fixed « Management service offline » issue, with an EDA500 unit attached and an orphaned volume record. – Fixed an issue where fan speed would fluctuate frequently on some models, especially at low speeds. I do step-by-step.– Fixed an issue where fan control was not working, resulting in fans spinning at their highest speed (RN3130/3138) My question is, if you install to the DOM, can you go back to the stock OS at some point? I'm not very familiar with this device, but is that where the stock OS is stored? Thus why I suggested installing to a flash drive, then if for some reason you didn't like OMV, all you'd have to do is remove the flash drive, and you' be back to the stock Thecus OS. But what was said above is 1000% accurate, RAID is not a backup, your data is not safe if it is only on a RAID. Unless it is some weird RAID that is unique to this device, it should be autodtected. Install to the DOM, boot OMV, run all updates, shutdown, and connect your data drives. Disconnect the data drives, so that only your installer (presumably a flash drive) and your OS drive (apparently your DOM) are the only two drives connected. Do I need to integrate this back into the RAID configuration somehow?įollow the general install instructions, and it should be fine. I think this last one is a special journal volume, but am not sure what to do with it. After installation 3 separate RAID volumes / filesystems were detected, md0(ext4, 11TB) with all my files, md10(swap) and md50(xfs,500MB). Under ThecusOS this speed was dynamic, based on system temperature, and it would by default spin very slow after boot-up.ģ. The system fan is spinning a bit too loud for my taste. These worked fine under the old 'ThecusOS'.Ģ. ![]() Raid access doesn't blink any of the leds that are present in each bay. Go there in your browser and finish setup.Īs of now I only have some minor things to fix, maybe others have some tips how to fix these:ġ. I did this by logging in as root with the password I configured during installation, then ran 'apt install net-tools' after which I could use the trusty ifconfig to see my nic config. Install OMV normally, see docs for details.įor me after install it didn't show the correct network interface configuration, so I had to look up the IP that was configured through DHCP. Set the installation media USB stick as first boot device in the BIOS. Power up your N5550 and press F2 as soon as you see the prompt.ħ. Connect a monitor to HDMI and a keyboard to USB on the back.Ħ. It's easy to use this port as you can't boot from it, so no USB boot priority issues.ĥ. Insert the USB stick you want to install OMV on in the front. Insert the installation media USB stick in a USB port on the back.Ĥ. This will trigger the shutdown procedure.ģ. Power down your N5550 through the web interface or by pressing the power button once. Build the installation media USB stick from the downloaded ISO, with Balena Etcher.Ģ. I'm surprised to see how easy the process went from downloading the ISO to a fully functioning OMV setup on my NAS If anyone needs a hand in doing the same, let me know, but I'm sure most can figure out the basics:ġ. One for installation media and the other for the OMV OS install. So I just installed OMV on my Thecus N5550 NAS, using 2 USB sticks.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |